Energy

Process Engineering, Design & Drafting

Mechanical Engineering, Design & Drafting

Mechanical Engineering, Design & Drafting

image26

  • Debottlenecking
  • Optimization 
  • Process simulation 
  • Line sizing
  • Valve sizing
  • PSV sizing
  • PSV sizing basis
  • Equipment sizing 
  • Efficiency upgrades
  • Chemical consumption calculation
  • Design basis
  • Design basis memorandum
  • Relief System design
  • Equipment datasheets
  • PFDs
  • Heat & material balance
  • P&IDs
  • Line list
  • Alarm & shutdown key
  • Process control philosophy
  • Car seal list
  • PSV list
  • P&ID checklist
  • Pump sizing
  • Separator sizing
  • Flare knockout drum sizing
  • Free water knockout sizing
  • Treater sizing
  • Flare stack sizing
  • Storage tank sizing
  • Pop tank sizing
  • PVRV sizing
  • EPRV sizing
  • Heat exchanger sizing
  • Dispersion modelling
  • Thief hatch sizing
  • Engineering report
  • API and ASME References
  • Fuel gas scrubber sizing
  • Meter run sizing
  • Orifice sizing
  • Insulation sizing
  • ABSA / BCSA registration
  • Compressor sizing
  • HAZOP
  • Bill of Materials (BOM)

Mechanical Engineering, Design & Drafting

Mechanical Engineering, Design & Drafting

Mechanical Engineering, Design & Drafting

image27

  • Bend selection
  • Anchor selection
  • Carbon steel wall thickness calcs
  • Stress analysis
  • Stainless steel tubing selection
  • Pipe class selection
  • Relief system design
  • Tie-in list
  • Pump design
  • Separator design
  • Flare knockout drum design
  • Free water knockout design
  • Engineering report
  • P. Eng check
  • P&ID checklist
  • Flexibilty analysis
  • Treater design
  • Flare stack design
  • Storage tank design
  • Pop tank design
  • Control valve design
  • Thief hatch design
  • Equipment MAWP ratings
  • Meter run design
  • Orifice design
  • Insulation design
  • Compressor design
  • Bill of materials (BOM)
  • Search/Obtain Existing Drawings
  • Drawing Index
  • P&IDs
  • Equipment modelling
  • Line modelling
  • Instrument modelling
  • Steel modelling
  • Clash check
  • Database check
  • Model audit
  • Plot plan
  • Stress isometrics
  • Isometrics (w/ BOM)
  • Heat tracing isometrics
  • Piping plans
  • Piping sections
  • Piping details

Electrical Engineering, Design & Drafting

Mechanical Engineering, Design & Drafting

Instrumentation Engineering, Design & Drafting

image28

  • Solar panel sizing and design
  • Single line diagram
  • Area classification
  • Power system study
  • Fugitive emissions study
  • Relay settings
  • Load calculations
  • Protective coordination
  • Load flow fault levels
  • Main Service, Transformer
  • Control Methods, Systems
  • Tray loading calculations
  • Voltage drop calculations
  • Lighting calculations
  • Cathodic protection
  • Power reliability study (optimization)
  • S/L-Pri, HV, MV, Substation
  • S/L - LV, Distn, MCC
  • Fiber optic layouts
  • Schematics - 5kV+ Power (MCC)
  • Schematics - 5kV Power (MCC)
  • Schematics - 480V or 600V Power (MCC)
  • Schematics - Low Voltage
  • Schematic - Control (Ltg)
  • Layout
  • Wiring Diagrams - Discrete (JB)
  • Wiring Diagrams - Power (JB)
  • Wiring/Block Diag - Instr/Cntl (JB)
  • Schedules - Conduit, Wire/Cable
  • Schedule - Panel
  • Schedule/ISO - Heat Tracing
  • Schedule - Other (B.O.M.)                  
  • Installation Details - Size A, B
  • Standard Details & Legend
  • Contactor Panel Layout
  • MV ( 1kV +) - Substn, Poleline
  • MV Switchgear
  • MV Motor Control, VFD
  • MV Transformer
  • MV Wire, Cable
  • MV Duct, Raceway
  • LV(600V-) Switchgear
  • Heat tracing

Instrumentation Engineering, Design & Drafting

Civil, Structural, Geotechnical Engineering, Design & Drafting

Instrumentation Engineering, Design & Drafting

image29

  • Sour gas detectors
  • LEL and UEL detectors
  • H2S analyzers
  • Moisture analyzers
  • Dew point analyzers
  • Pressure transmitter
  • Pressure switch
  • Temperature transmitter
  • Temperature switch
  • Flow transmitter
  • Flow switch
  • Flow meter
  • Index/Loop Count
  • Intools Wiring Modules
  • Location Drawings
  • Control Room Layouts

Civil, Structural, Geotechnical Engineering, Design & Drafting

Civil, Structural, Geotechnical Engineering, Design & Drafting

Civil, Structural, Geotechnical Engineering, Design & Drafting

image30

  • Geotechnical Study Review
  • Site preparation design
  • Underground requirements
  • Soil testing and evaluation
  • Fireproofing design
  • Piperack designs
  • Structural frame design
  • Equipment supports
  • Piping supports
  • Building design
  • Loading/Unloading Check
  • Storage Tank
  • Lug Design / Check
  • Lifting Design & Diagram
  • Foundation design
  • Piling Foundation Design

Project Management, Project Engineering, and Regulatory

Civil, Structural, Geotechnical Engineering, Design & Drafting

Civil, Structural, Geotechnical Engineering, Design & Drafting

image31

  • Kick-off Meeting
  • Design Basis
  • Design Basis Memorandum (DBM)
  • Manhour Estimates
  • Drawing Controls
  • Schedules
  • Cost Control
  • Site Visits
  • Project Meetings/Integratation alignment
  • Design Meetings
  • Deliverable Controls
  • Manhour Control & Reporting (DRPT)
  • Interdiscipline Meetings

Featured Projects

Rail-loading Facility

Amine Filter Replacement

Amine Filter Replacement

Tidewater rail loading facility Acheson, AB

Tidewater Midstream was building a new rail loading facility in Acheson, AB and required electrical engineering and design for it. Forte provided a complete electrical engineering package.

Amine Filter Replacement

Amine Filter Replacement

Amine Filter Replacement

image32

Enbridge was replacing their Amine system and required mechanical and electrical design and engineering. Forte provided a complete drawing package issued for construction

Experience

image33
image34
image35
image36
image37
image38

Get In Touch

Drop us a line and we'll get back to you ASAP!

Better yet, see us in person!

We love our customers, so feel free to visit during normal business hours.

Forte Engineering Solutions Inc

639 5 Avenue SW, Suite 2500, Calgary, Alberta T2P 0M9, Canada

(403) 775-2266 info@forteengsolutions.com sales@forteengsolutions.com

Hours

Open today

08:00 a.m. – 06:00 p.m.

Subscribe

Sign up to get free project tips